- MKMichael K.Verified Buyer1 week agoRated 5 out of 5 starsBomber for Tesla Model S and 2 ebikes
Looked high and low for a bike rack that doesnt require a trailer hitch, works on a Tesla Model S and 3 without risky clips and straps, and is compatible with our two heavy e-bikes. The Bomber fit the bill. Like all the reviews of the SeaSucker system I have read, I was nervous at first, especially putting two ebikes weighing 50 lbs each (with battery and front wheel removed) on this rack, although this is comfortably within the 135 lb overall weight rating for the Bomber. The Bomber is a cinch to set up - my 2016 model S does not have a glass roof, so I put the main rack at the rear of the metal roof near the glass seam - likely the strongest part of the roof, as near as I can tell - and the rear wheel on the lip of the trunk (see photo). By far the hardest part was lifting those heavy bikes up onto the car and hooking in the fork mount - easy with 2 people, a struggle for me by myself at age 67, but i have learned a few tricks to make it easier to do solo. The rack is rock solid and I have taken the two ebikes on a 200 mile trip into the mountains at interstate speeds and on local roads with no issues. Note: make your own assessment about what is a safe use of this product - use at your own risk. But for me, the Bomber is....well, the bomb!
- DMDavid M.Verified Reviewer2 months agoRated 5 out of 5 starsGreat products and company!!!
I approached Seasucker to help raise awareness for safer streets for all to use as I build and place Ghost Bikes for fallen cyclists in the southeast! The Bomber 3 bike rack is awesome and I've traveled 18 hours on a 1165 mile trip to place 3 bikes in Ga/Ala/Fl!! This rack is flawless and works super. Thanks for your help in this journey for safer streets for all to use!! #NFOFF Bikefriendlyatl, Inc
- JBJim B.Verified Buyer11 months agoRated 5 out of 5 starsGreat Product, Measure your car!
Love the bomber, works great. I did not measure my room, assuming it had to fit and at a certain part of the roof it is millimeters away from the seam, and would not work if it crossed that. My fault for not measuring, but I am lucky. Works amazing.
- BPBrooke P.Verified Buyer6 days agoRated 3 out of 5 starsGreat product... but there are compromises
I bought this for my SUV that lacks either a hitch or roof rails. After much research I settled on the SeaSucker for its low cost relative to other options (which would require installing a hitch or rails) and because it needed to be usable by my wife who cannot lift a bike onto the roof of our tall car. And it works, but not without tradeoffs:
- For me, it was about 1/2 or even 1/3 the cost of other 3 bike options
- Quick and easy to install (for me... see below)
- Strong and secure hold with no worries
- Great to be able to hold three bikes
- Have to remove the front wheel, which means taking up precious cargo space. Not ideal if you're going on a multi-day trip with bikes.
- Can't open the back once the bikes are mounted (don't forget to put the wheels in before closing!)
- The fork mounts are secure but a real wrestle at times and my wife could not do it on her own with a heavier mountain bike. You need to be able to hold the bike in place with one hand while you tighten the QR with the other. It's not easy even for someone well practiced in mounting bikes and wheels and for some it's a two person operation.
- The back window on my Acura MDX is curved so you need to bend the Bomber to get contact with all the suction cups. There is flex in the platform so it's possible but it requires more strength and leverage than my wife can apply. So she cannot mount without my help. If you have a curved back window be prepared to have to use some muscle.
- No way to…SSeaSucker6 days ago
Thanks for the review. We do have locks for the racks, see link below:
- FLFreddy L.Verified Buyer3 months agoRated 5 out of 5 starsGreat Bike Rack!
This is by far the most convenient and useful bike ride I’ve owned. It’s sturdy, easy to install, doesn’t damage my car, and easy to take my bike off. Highly suggest.
We've speed tested our racks over 175 mph, in controlled conditions and with adequate safety measures. Nevertheless, going above the speed limit violates the SeaSucker warranty. You must obey all posted speed limits and traffic conditions; if there is no posted speed limit, we recommend not driving above 85 miles per hour. You must adapt your driving style and speed to road conditions, weather conditions, and the load on your SeaSucker rack.
If you can remove your front wheel and your bike’s fork is made for one of the following sizes, you can use the rack: 9x100mm Quick Release; 12x100mm Thru-Axle; 15x100mm Thru-Axle, 15x110mm Thru-Axle, 20x100mm Thru-Axle, or 20x110mm Thru-Axle. These six sizes handle 99% of what’s out there, including road, cross, and gravel bikes, cruisers, and mountain and BMX bikes. Fat bike riders can use SeaSucker racks too, but you’ll need the proper Fork Up fork mount adapter to fit your bike.
Absolutely. Sometimes we say “wetter is better” around here, but don’t take that in a weird way. SeaSuckers will typically hold better when wet, so the rain is no problem. With regard to snow and cold, be aware that if you remove your rack after using it in the cold, you may have to warm it up again to near room temperature before the rubber is pliable enough to make a solid seal to the mounting surface. Once it’s mounted (or if you didn’t remove it), you’re good to go. Also, for warmer weather we recommend that you wet the sealing edge of your rack before attaching. DO NOT DO THIS IN FREEZING OR NEAR-FREEZING TEMPERATURES. The vacuum cup will freeze to the surface of your car, which will prevent the vacuum pump and check valve from functioning properly. You’re still going to have to wipe your car clean in the cold, since the vacuum mounts won’t mount if there’s snow or ice on the car. Make sure to dry it before attaching your rack!
No, the vacuum pads, which are the only parts of the SeaSucker vacuum mounts that should touch your car, are made of the non-marking rubber compound.
We don’t recommend using our products on wrapped vehicles. Our testing shows that our vacuum cups will pull a bubble in the wrap when attached, which screws up the wrap and is not a safe attachment point for a SeaSucker. To make it work, some people have removed the wrap just where the vacuum mounts will sit on their vehicle. However, you are absolutely able to use a SeaSucker rack on a ceramic coated car.
We recommend that you mount your rack where your roof has supportive structure underneath, like just behind the front windshield or just in front of the rear window. Unsupported areas, like in the very middle of a roof, can flex when driving over bumpy roads.
Yes. Most SeaSucker bike racks are fork-mount racks, meaning your front fork gets clamped onto the rack for transport. You have to remove your front wheel to do this. The exception is our Hornet 1-bike rack; check it out here: https://www.seasucker.com/products/hornet?_pos=2&_sid=62cab0749&_ss=r
SeaSucker racks are generally recognized as the easiest and fastest to install. We’re contemplating calling Guinness for official certification. As for an actual time, that depends on your motivation and pumping speed. We’ve seen a Talon rack installed in as few as 8 seconds!
Every SeaSucker vacuum mount has an indicator band right on the plunger. When the vacuum mount starts losing vacuum, the plunger will begin to extend. When it extends far enough that you can see the orange band, it’s time to re-pump. Unlike traditional suction cups, with SeaSucker, you don’t have to take it off and lick it (unless you’re into that sort of thing, and we don’t judge) to revive it.
In addition to selling complete vacuum mounts that you could swap in for one that’s been damaged, we also sell replacement parts such as new vacuum pads and pumps.
“Strong like bull.” 4.5” vacuum mounts have a rated pull strength of 120lbs, pulling straight out from center. Pull strength on a shear load, i.e. pulling from the side, will be less. 6” vacuum mounts are 210lbs rated. Obviously, putting multiple vacuum mounts on a single product multiplies the maximum holding power.
The bug will be obliterated; please take a second to honor its sacrifice. If the debris isn’t big enough to put a dent in your car, you have nothing to worry about. If it is, then you have bigger problems.
There’s no set time limit on our vacuum mounts. It depends in part on the surface you attach to, the condition of the vacuum mount, the load you put on it, and other factors. As for surfaces to attach to, vacuum mounts in general were designed to carry big sheets of glass and other solid surface materials, so smoother, flatter surfaces are ideal. Clean surfaces and clean SeaSuckers go a long way to maximizing the hold time. In any event, if the vacuum mount begins to lose some vacuum, it will warn you so you can get it back to full power before it comes off. The vacuum pump’s plunger will extend from the pump cylinder when it starts to lose power, revealing an orange indicator band. Once you see orange, that’s your cue to repump your SeaSucker. For car racks, the simplest thing to do is to check the rack before you get in your vehicle, and check it each time you stop for gas, food, or the bathroom.
Your bike should always be facing forward on the car, but the rack itself can be mounted “backwards”. You might want to do this for a better fit on either the roof, trunk, or hatch. Flipping the rack can often troubleshoot fit issues, such as a chain ring coming into contact with a rear hatch.
Vacuum mounts in general were designed to carry big sheets of glass and other solid surface materials, so smoother, flatter surfaces are ideal. Very shallow texture may be okay, but should be tested (to test, attach the rack to the car and make sure the orange indicator bands are not showing after two hours of just sitting in your driveway). If the sealing edge of the vacuum pad doesn’t make a complete connection with the mounting surface, air will leak in through any gaps and will release the vacuum.
Our basic warranty used to be just one year, but these things are so reliable we've extended it to a limited lifetime warranty. It covers the original purchaser against defects in materials and workmanship but not normal wear and tear. This is our warranty: SeaSucker offers a lifetime, non-transferable warranty to the original purchaser covering defects in materials and workmanship. Defective products can be returned to SeaSucker for replacement or repair (at SeaSucker’s option). Warranty claims must be accompanied by a sales receipt or other proof of purchase document. The cost of transportation to and from SeaSucker for the repair or replacement of any defective part or accessory is not covered by this warranty and is to be paid by the owner.
This warranty does not apply to damage or failure resulting from routine wear and tear expected in the normal use of this product, or to lack of maintenance, user error, alteration or modification of the product, accidents, misuse, abuse, or neglect.
This warranty is given in lieu of all other written or oral warranties, express or implied, including without limitation implied warranties of merchantability and fitness for a particular purpose, and are limited to the duration and specifications of this warranty.
Purchaser’s exclusive remedy under this warranty is the repair or replacement of a defective product or, at SeaSucker’s option, the issuance of a refund or credit for the purchase price of the product. SeaSucker’s liability for any damages relating to any allegedly defective product, whether arising from the use or the inability to use the product and whether claimed under tort, contract or any other legal theory, shall be limited to the actual price paid for such product and shall in no event include loss of use, loss of time, incidental, consequential, special, or indirect damages of any kind, even if SeaSucker is aware of the possibility of such damages, to the full extent as such may be disclaimed by law.
It is the user’s responsibility to ensure that the use of this product is not prohibited by any applicable local or state law.
Clean off any surface dirt from the mounting surface before attaching your SeaSucker. While you’re at it, make sure the sealing edge of the vacuum pad is clean too. You don’t have to clean the mounting surface with alcohol wipes, as one overly-enthusiastic customer told us they do, but a quick wipe with a wet paper towel or napkin wouldn’t hurt. Let us make it easy for you: get one of our Cleaning Kits.
No, the HDPE and the raw materials we use to manufacture our vacuum mounts all have a high-performance UV inhibitor built in. Your SeaSucker products should look good for years.
The orange indicator band is a visual representation of how much vacuum power your cup has. Once you start to see the orange indicator band, that means it’s time to pump your product back up!
SeaSucker products are proudly made in the USA. We go from raw materials to finished products all from our factory in Bradenton, Florida.