If you’re axle-deep in sand or mud every weekend, you need a safe and convenient way to mount your Hi Lift Jack that doesn’t require drilling into your truck’s sheet metal. SeaSucker’s Recovery Mounts are on the case. Simply thread the mount’s bolt through the holes on your jack, spin on the anodized aluminum lock knob, and pump the powerful 4.5" SeaSucker vacuum mounts for a secure hold. Hi Lift Jack Mount come four per set, so you have plenty of different mounting configurations to choose from.
Couldn't load pickup availability
SeaSucker's got you covered! Check out all of the latest releases to our innovative Overland & RV Accessory Collection.
Works with most recovery board and jack brands.
Each set of Recovery Mounts holds up to two recovery boards or one recovery jack.
- Q: How strong are the vacuum mounts?
- A: “Strong like bull.” 4.5” vacuum mounts have a rated pull strength of 120lbs, pulling straight out from center. Pull strength on a shear load, i.e. pulling from the side, will be less. 6” vacuum mounts are 210lbs rated. Obviously, putting multiple vacuum mounts on a single product multiplies the maximum holding power.
- Q: How long do the vacuum mounts last before they lose power?
- A: There’s no set time limit on our vacuum mounts. It depends in part on the surface you attach to, the condition of the vacuum mount, the load you put on it, and other factors. As for surfaces to attach to, vacuum mounts in general were designed to carry big sheets of glass and other solid surface materials, so smoother, flatter surfaces are ideal. Clean surfaces and clean SeaSuckers go a long way to maximizing the hold time. In any event, if the vacuum mount begins to lose some vacuum, it will warn you so you can get it back to full power before it comes off. The vacuum pump’s plunger will extend from the pump cylinder when it starts to lose power, revealing an orange indicator band. Once you see orange, that’s your cue to repump your SeaSucker. For car racks, the simplest thing to do is to check the rack before you get in your vehicle, and check it each time you stop for gas, food, or the bathroom.
- Q: Do I need to clean the surface I’m going to attach my SeaSucker to?
- A: Clean off any surface dirt from the mounting surface before attaching your SeaSucker. While you’re at it, make sure the sealing edge of the vacuum pad is clean too. You don’t have to clean the mounting surface with alcohol wipes, as one overly-enthusiastic customer told us they do, but a quick wipe with a wet paper towel or napkin wouldn’t hurt. Let us make it easy for you: get one of our Cleaning Kits.
- - Anodized aluminum bolting hardware
- - Back deck is made of super durable HDPE
- - Each individual mount is powered by a powerful 120lb pull-strength rated 4.5" vacuum mount
Customer Reviews
- TSThomas S.Verified Buyer12 hours agoRated 5 out of 5 starsAwesome!
These things are awesome. The modularity and the possibilities are endless. I've rigged my Wrangler so that I can take the RTT off when I'm not using it so being able to remove the maxtraxx as well is huge for me. I don't want to be that guy that has his car fully rigged 365.
- MWMichael W.Verified Buyer4 weeks agoRated 5 out of 5 starsSolid mount
Great product, mounts well. Looking forward to taking it out on the trail.
- GSGiovanni S.Verified Buyer1 month agoRated 5 out of 5 starsPerfect mounting solution
These are the perfect mounting solution for me. I daily drive my off-roading truck and these suction cups make it easy to mount on/off on a as-need basis without too much hassle. I’ve been mounting them on the hood of my truck and have done 75 mph with head and cross winds with no issues at all. Plus they look cool as hell!
Look forward to using some of the other sea sucker mounting solutions in the future.
SSeaSucker1 month agoGreat pic!
- BMBenjamin M.Verified Buyer1 month agoRated 5 out of 5 starsGreat mounting solution
Great option for vehicles that don’t have as much aftermarket support as some other popular vehicles do. Only issue is the mounts don’t support traction boards that are thicker than some other brands but was able to work around that with some additional hardware. Would definitely buy again if I had to!
SSeaSucker1 month agoHey Ben,
New version coming out soon!
- JMJames M.Verified Buyer4 months agoRated 5 out of 5 starsGood suckage
These work great to mount my ARB recovery boards to the top of my Tentrax trailer. Needed larger washers than the ones supplied.
FAQS
“Strong like bull.” 4.5” vacuum mounts have a rated pull strength of 120lbs, pulling straight out from center. Pull strength on a shear load, i.e. pulling from the side, will be less. 6” vacuum mounts are 210lbs rated. Obviously, putting multiple vacuum mounts on a single product multiplies the maximum holding power.
There’s no set time limit on our vacuum mounts. It depends in part on the surface you attach to, the condition of the vacuum mount, the load you put on it, and other factors. As for surfaces to attach to, vacuum mounts in general were designed to carry big sheets of glass and other solid surface materials, so smoother, flatter surfaces are ideal. Clean surfaces and clean SeaSuckers go a long way to maximizing the hold time. In any event, if the vacuum mount begins to lose some vacuum, it will warn you so you can get it back to full power before it comes off. The vacuum pump’s plunger will extend from the pump cylinder when it starts to lose power, revealing an orange indicator band. Once you see orange, that’s your cue to repump your SeaSucker. For car racks, the simplest thing to do is to check the rack before you get in your vehicle, and check it each time you stop for gas, food, or the bathroom.
Clean off any surface dirt from the mounting surface before attaching your SeaSucker. While you’re at it, make sure the sealing edge of the vacuum pad is clean too. You don’t have to clean the mounting surface with alcohol wipes, as one overly-enthusiastic customer told us they do, but a quick wipe with a wet paper towel or napkin wouldn’t hurt. Let us make it easy for you: get one of our Cleaning Kits.
Use this text to share information about your brand with your customers. Describe a product, share announcements, or welcome customers to your store.
Where are SeaSucker products made?
SeaSucker products are proudly made in the USA. We go from raw materials to finished products all from our factory in Bradenton, Florida.
OFFICIAL PARTNER TO THE UCI & TEAM JUMBO VISMA
Innovation is the foundation of our company. Our founder, Chuck Casagrande, has invented well over 200 different products to date. Every year SeaSucker works to introduce more and more creative solutions for the athlete or angler on the go.
SeaSucker’s R&D team promise to continue to provide consumers with premium products centered on innovation.
READ MORE READ LESS
WATCH
WINNING TEAM
Don't Forget to Add Plugs to your Cart!
HUSKE 12x100mm Thru-Axle Plugs
HUSKE 15x100mm Thru-Axle Plugs
HUSKE 15x110mm Thru-Axle Plugs (Boost)
HUSKE 20x110mm Thru-Axle Plugs
HUSKE 20x100mm Thru-Axle Plugs
HUSKE 9x100mm Quick Release Plugs w/ QR Axle
HUSKE 9x100mm Quick Release Plugs - No Axle
It's time to select the right HUSKE Plugs to fit your bike. If you don’t know what front hub your bike has, it’s not that hard to figure out - all you have to do is measure it.
First, get a ruler or tape measure showing millimeters (sorry Americans, the bike world is firmly in the grip of METRIC TYRANNY!).
Step 1: measure the diameter of the hole at the end of your forks - it will be either 9mm, 12mm, 15mm or 20mm.
Step 2: measure the distance between the holes on your fork - it will be either 100mm or 110mm. Now purchase the HUSKE Plugs that match your measurements. There’s a color coded chart below that will help you make sure you’re buying the right set.
