- JMJames M.Verified Buyer2 weeks agoRated 5 out of 5 starsGood suckage
These work great to mount my ARB recovery boards to the top of my Tentrax trailer. Needed larger washers than the ones supplied.
- GGrahamVerified Buyer3 months agoRated 4 out of 5 starsGreat Board Carriers
These Recovery board carriers were just what I needed.
The opportunity to secure my boards without mounting anything permanent to my ride was HUGE!
These hold great on auto glass & installation was super easy. I avoided mounting to the body panels b/c my Van is wrapped.
- GGGordon G.Verified Buyer2 days agoRated 5 out of 5 starsRecovery Mounts
- JAJonathan A.Verified Buyer3 months agoRated 5 out of 5 starsWorks well
Works well on the side of my van
“Strong like bull.” 4.5” vacuum mounts have a rated pull strength of 120lbs, pulling straight out from center. Pull strength on a shear load, i.e. pulling from the side, will be less. 6” vacuum mounts are 210lbs rated. Obviously, putting multiple vacuum mounts on a single product multiplies the maximum holding power.
There’s no set time limit on our vacuum mounts. It depends in part on the surface you attach to, the condition of the vacuum mount, the load you put on it, and other factors. As for surfaces to attach to, vacuum mounts in general were designed to carry big sheets of glass and other solid surface materials, so smoother, flatter surfaces are ideal. Clean surfaces and clean SeaSuckers go a long way to maximizing the hold time. In any event, if the vacuum mount begins to lose some vacuum, it will warn you so you can get it back to full power before it comes off. The vacuum pump’s plunger will extend from the pump cylinder when it starts to lose power, revealing an orange indicator band. Once you see orange, that’s your cue to repump your SeaSucker. For car racks, the simplest thing to do is to check the rack before you get in your vehicle, and check it each time you stop for gas, food, or the bathroom.
Clean off any surface dirt from the mounting surface before attaching your SeaSucker. While you’re at it, make sure the sealing edge of the vacuum pad is clean too. You don’t have to clean the mounting surface with alcohol wipes, as one overly-enthusiastic customer told us they do, but a quick wipe with a wet paper towel or napkin wouldn’t hurt. Let us make it easy for you: get one of our Cleaning Kits.
No, the HDPE and the raw materials we use to manufacture our vacuum mounts all have a high-performance UV inhibitor built in. Your SeaSucker products should look good for years.
Where are SeaSucker products made?
SeaSucker products are proudly made in the USA. We go from raw materials to finished products all from our factory in Bradenton, Florida.
Don't Forget to Add Plugs to your Cart!
HUSKE 12x100mm Thru-Axle Plugs
HUSKE 15x100mm Thru-Axle Plugs
HUSKE 15x110mm Thru-Axle Plugs (Boost)
HUSKE 20x110mm Thru-Axle Plugs
HUSKE 20x100mm Thru-Axle Plugs
HUSKE 9x100mm Quick Release Plugs w/ QR Axle
HUSKE 9x100mm Quick Release Plugs - No Axle
It's time to select the right HUSKE Plugs to fit your bike. If you don’t know what front hub your bike has, it’s not that hard to figure out - all you have to do is measure it.
First, get a ruler or tape measure showing millimeters (sorry Americans, the bike world is firmly in the grip of METRIC TYRANNY!).
Step 1: measure the diameter of the hole at the end of your forks - it will be either 9mm, 12mm, 15mm or 20mm.
Step 2: measure the distance between the holes on your fork - it will be either 100mm or 110mm. Now purchase the HUSKE Plugs that match your measurements. There’s a color coded chart below that will help you make sure you’re buying the right set.