US / en
Let us help you haul your RotopaX Tanks without any permanent mounts! Grab a SeaSucker RotopaX Tank Holder, powered by two 6" SeaSucker mounts, and easily attach your existing tank and hardware. Put your tanks on when you need them, remove in seconds when you don't! SeaSucker's RotopaX Tank Holder is compatible with any RotopaX tank up to three gallons. No matter what you're hauling, SeaSucker will make your next overlanding adventure easier.
If you select to purchase with hardware, the included hardware is the DLX Pack Mount.
Purchase diesel, gasoline, or water tanks separately here.
Couldn't load pickup availability
SeaSucker's got you covered! Check out all of the latest releases to our innovative Overland & RV Accessory Collection.
- - Designed to hold any RotopaX tank up to 3 gallons. RotopaX tank and hardware are not included.
- - It is recommended that you mount the RotopaX Tank Holder on a vertical surface (back glass on SUV, side window of van) with the mounts stacked vertically.
- Q: How strong are the vacuum mounts?
- A: “Strong like bull.” 4.5” vacuum mounts have a rated pull strength of 120lbs, pulling straight out from center. Pull strength on a shear load, i.e. pulling from the side, will be less. 6” vacuum mounts are 210lbs rated. Obviously, putting multiple vacuum mounts on a single product multiplies the maximum holding power.
- Q: How long do the vacuum mounts last before they lose power?
- A: There’s no set time limit on our vacuum mounts. It depends in part on the surface you attach to, the condition of the vacuum mount, the load you put on it, and other factors. As for surfaces to attach to, vacuum mounts in general were designed to carry big sheets of glass and other solid surface materials, so smoother, flatter surfaces are ideal. Clean surfaces and clean SeaSuckers go a long way to maximizing the hold time. In any event, if the vacuum mount begins to lose some vacuum, it will warn you so you can get it back to full power before it comes off. The vacuum pump’s plunger will extend from the pump cylinder when it starts to lose power, revealing an orange indicator band. Once you see orange, that’s your cue to repump your SeaSucker. For car racks, the simplest thing to do is to check the rack before you get in your vehicle, and check it each time you stop for gas, food, or the bathroom.
- Q: Do I need to clean the surface I’m going to attach my SeaSucker to?
- A: Clean off any surface dirt from the mounting surface before attaching your SeaSucker. While you’re at it, make sure the sealing edge of the vacuum pad is clean too. You don’t have to clean the mounting surface with alcohol wipes, as one overly-enthusiastic customer told us they do, but a quick wipe with a wet paper towel or napkin wouldn’t hurt. Let us make it easy for you: get one of our Cleaning Kits.
- - Made to hold any RotopaX tank up to 3 lb.
- - Attaches to metal, glass or fiberglass surfaces.
- - 3/8" thick high-density polyethylene (HDPE) deck for strength and durability.
- - When mounted vertically: approx. 15" tall, 2.75" deep, 6.5" wide
- - Approx. 2.05 lb.
- - Powered by two 6" SeaSucker mounts.
Customer Reviews
- DLDennis L.Verified Buyer4 months agoRated 5 out of 5 starsConvenient and durable
Very easy to put on and remove, extremely sturdy and well designed with durable materials. Works especially well for crossovers that don't have racks in place to hold fuel tanks.
- SBsteven b.Verified Buyer5 months agoRated 5 out of 5 starsGreat so far
Quite the attention getter at the coffee meet up
“Suction cups?!”
Light duty in Anza Borrego , so far so good.
- PTphillip t.Verified Buyer6 months agoRated 5 out of 5 starsEasy install. Nice 👍
Perfect fit for my outback wilderness . Strong and sturdy highly recommended
- PEPAUL E.Verified Buyer7 months agoRated 5 out of 5 starsI was skeptical... However,
I've had the RotopaX Tank Holder on my 4-door JK for about a month and they are holding on extremely well. Within that month they took a 3000 mile round trip from Central Ohio to Deadwood, South Dakota. During the trip they experienced: Interstate 70 across Indiana (IYKYK), extreme gusty head winds crossing South Dakota on Interstate 90, and moderate to heavy wheeling during the Black Hills Jeepers Jamboree. I am very happy with these mounts and highly recommend them to anyone looking for a simple solution to secure rotopaXs to your rig.
- MBMichael B.Verified Buyer7 months agoRated 5 out of 5 starsSaved the family trip
Used with the 3 gallon rotopax to get the family home safely this holiday weekend when a 50 mile stretch of highway service stations were out of gas! Product was mounted to the trailer and worked without any issues. Thank you.
OFFICIAL PARTNER TO THE UCI & TEAM JUMBO VISMA
Innovation is the foundation of our company. Our founder, Chuck Casagrande, has invented well over 200 different products to date. Every year SeaSucker works to introduce more and more creative solutions for the athlete or angler on the go.
SeaSucker’s R&D team promise to continue to provide consumers with premium products centered on innovation.
READ MORE READ LESS
WATCH
WINNING TEAM
Don't Forget to Add Plugs to your Cart!
HUSKE 12x100mm Thru-Axle Plugs
HUSKE 15x100mm Thru-Axle Plugs
HUSKE 15x110mm Thru-Axle Plugs (Boost)
HUSKE 20x110mm Thru-Axle Plugs
HUSKE 20x100mm Thru-Axle Plugs
HUSKE 9x100mm Quick Release Plugs w/ QR Axle
HUSKE 9x100mm Quick Release Plugs - No Axle
HUSKE 5x100mm
HUSKE 12x110mm
It's time to select the right HUSKE Plugs to fit your bike. If you don’t know what front hub your bike has, it’s not that hard to figure out - all you have to do is measure it.
First, get a ruler or tape measure showing millimeters (sorry Americans, the bike world is firmly in the grip of METRIC TYRANNY!).
Step 1: measure the diameter of the hole at the end of your forks - it will be either 9mm, 12mm, 15mm or 20mm.
Step 2: measure the distance between the holes on your fork - it will be either 100mm or 110mm. Now purchase the HUSKE Plugs that match your measurements. There’s a color coded chart below that will help you make sure you’re buying the right set.
